Connecting Computer or Smartphone to Printer Directly via Wireless LAN (Access Point Mode)

The printer has a function to connect a computer or smartphone to the printer directly via wireless LAN, allowing you to perform printing operation.Follow the procedure below to use this function.

For more on printing operation, refer to device's or application's instruction manual.

Important

Connecting Computer or Smartphone to Printer Directly via Wireless LAN (Access Point Mode). The printer has a function to connect a computer or smartphone to the printer directly via wireless LAN, allowing you to perform printing operation. Follow the procedure below to use this function. Change printer setting. Connect computer or smartphone to printer. As the title says in this video I will show you how to reset the Waste Ink Counter of the Canon Pixma iP90 and iP90v printers.PLEASE REPLACE YOUR INK ABSORBE.

If a device has already been connected to the printer via wireless LAN and you want to add a device to connect, connect it to the printer directly.You can connect up to 5 devices to the printer at the same time.
For restrictions when you change the connection method from direct connection to connection via a wireless router:

Changing Printer Setting

Change the printer setting following the procedure below.

Press and hold Wi-Fi button and release it when POWER lamp flashes 3 times.
Make sure POWER lamp changed from flashing to lit.
If the POWER lamp is not lit, repeat step 2.

Note

To check the current access point mode setting of the printer, print out the network setting information.
You can change the security setting using IJ Network Tool (bundled software).

Connecting Device to Printer

Important

Before connecting a computer to the printer and start printing with the method below, complete setup for wireless LAN (via a wireless router) from our website (canon.com/ijsetup).

Turn on wireless communication on your computer or smartphone.
For Android or iOS, enable 'Wi-Fi' on your device's 'Setting' menu.For more on the procedure, refer to device's instruction manual.
For iOS:
Select 'XXXXXX-iP110series' ('XXXXXX' represents last six digits of printer's MAC address.) from SSID list displayed on device.
Enter password.
The printer serial number is specified as a default password.It is printed on the sticker attached on the printer rear and consists of 9 alphanumeric characters (four alphabets followed by five numbers).
Note
- To check printer's serial number, print out the network setting information.
Connection is completed.

Performing Printing Operation

Start printing from the connected device.

CanonGENERIC 'S' SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will 'reset'
or move momentarily. If the above was properly performed the printer will enter the
'Service Mode'.
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to 'set' the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

++++++++++

Canoni320, i255
Waste Ink Counter Reset.
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark 'After service mode Pls use software for permanent reset'

++++++++++

Canon PIXMAiP1000
Waste Ink Counter Reset.
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

++++++++++

Canon PIXMAiP1500
Waste Ink Counter Reset.
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

Canon Ip100 Reset

++++++++++
Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2presses - green - EEPROM initialize
3presses - orange - Reset waste ink counter

How Do I Reset My Canon Ip100 Printer

++++++++++